Weber · Parts & Accessories
Weber Replacement Parts Guide: Flavorizer Bars, Igniters, Covers, and Regulators
Weber sells replacement parts through its own parts catalog and through the authorized dealer network — the serial number on the grill is the fastest route to the right part. For covers, Flavorizer bars, and grates, series and model year are the two things you have to match.
By Reed · Updated November 9, 2026
What you need
- Flashlight (for finding the serial plate)
- Phone camera (for photographing the serial plate)
- Tape measure (for cover sizing)
- Owner's manual (or the part number from a prior order)
Step by step
Find your model and serial number
On Spirit and Genesis, the serial plate is on the inside of the right-hand cabinet door or on the frame rail under the cook box. On a kettle, look under the One-Touch cleaning system label or inside the bowl near the gas inlet on a Performer. On Searwood pellet grills, the plate is on the back panel. Photograph the plate before you order — Weber's parts system is serial-driven for warranty-covered claims.
Decide which part you actually need
The three most-replaced Weber parts: Flavorizer bars (every three to five years for daily grillers), igniter kits (every five to seven years once the clicker stops firing), and covers (every two to three seasons in harsh climates). Burner tubes last 10 years on current models and are often warranty-covered if they fail inside that window. Regulators themselves rarely fail — the QCC1 bypass mode is almost always the real diagnosis, and it resets in 60 seconds without a new part.
Match Flavorizer bars to the series and model year
This is where most Weber parts orders go wrong. Spirit 200-series and 300-series take different bar sets; Genesis 300-series with front-mounted controls takes a different set than side-mounted controls; the 2013-2024 Spirit II generation takes bars that are not interchangeable with the current 2024-plus Spirit. Read the model year off your serial plate and match the bar SKU to it — the dimensions look almost identical but the hooks and lengths differ by a fraction of an inch.
Match the cover to the series and model year
The 2022-plus new-Genesis premium cover fits the current Genesis E/S/SX 300-series or 400-series — pick the number that matches your burner count. Older Genesis II and Genesis 300-series grills (pre-2022) take a different cover line. Searwood 600 takes its own cover; Searwood XL 600 takes a larger one. Q 2800N covers come in freestanding and on-cart versions because the cart base changes the cutout.
Order through weber.com, an authorized dealer, or the service center network
Direct part orders go through weber.com/parts or the Weber Service Center locator. Authorized dealers (including bbqs.com) stock the fast-moving SKUs for same-week shipping. Warranty-covered parts require the serial number and proof of purchase through the Weber support portal at support.weber.com. Weber's QCC1 regulator hose kit (part 7627 for 30-inch Genesis 300) is one of the few model-specific parts dealers routinely stock.
Common mistakes
- Ordering Flavorizer bars by burner count alone. A five-pack of Flavorizer bars fits a three-burner Genesis 300 AND a three-burner Spirit 300 — but the two sets are different lengths. Match the series and the model year, not the burner count.
- Replacing the regulator before trying the bypass reset. The QCC1 regulator enters bypass mode after a fast-close cylinder valve or a leak-test trip. The reset procedure — close the tank valve, disconnect the hose, open all burner knobs for one minute, reconnect, open the tank slowly — takes 60 seconds and fixes 80 percent of the regulators people replace.
- Using a generic hose-and-regulator kit. Weber's QCC1 fitting is spec'd to the grill's BTU rating. A generic high-flow regulator from a hardware store will often sit in bypass under normal flow and leave you with a grill that only reaches 350 degrees. Order Weber's own kit — 7627 for 30-inch Genesis 300, 7502 for 21-inch universal.
- Buying an aftermarket cover for a current-model Weber. A generic 60-inch cover that nominally fits a Genesis will usually sit loose at the hopper or hang short at the side burner. Weber's own covers are cut to the current-model dimensions and have the UV-rated fabric the catalog photo implies.
Hands-on tips
- Photograph the serial plate once, store it in a shared phone album, and you will never dig through the cabinet door again.
- Keep a spare pack of Flavorizer bars on the shelf — $40 beats cancelling a weekend cook because yours warped mid-brisket.
- Replace the Weber grill brush every spring. Weber's own cold-grill brush is $30 and you will not be picking bristles out of a rib-eye.
- If you own a Weber Connect-equipped SX or Summit, keep a spare probe in the drawer — the sensor degrades faster than the grill does and it ships in a few days from weber.com.
- Buy the matching cover when you buy the grill, not three weeks later when the grill is already sitting in the rain.
- Keep a backup igniter battery in the drawer; most current Weber electronic ignitions take a single AA.
Questions people ask
Where do I find my Weber grill's model and serial number?
On Spirit and Genesis gas grills, look inside the right-hand cabinet door or on the frame rail beneath the cook box. On Weber kettles, check under the One-Touch cleaning system label or inside the bowl. On Searwood pellet grills, the plate is on the back panel. Photograph it before you order any part.
Can I buy Weber replacement parts directly from Weber?
Yes — weber.com/parts and the Weber Service Center locator handle direct orders. Authorized dealers (including bbqs.com) stock the fast-moving SKUs for same-week shipping. Warranty-covered claims require the serial number and proof of purchase through support.weber.com.
How often should I replace Flavorizer bars?
Every three to five years for a weekly griller. Warped, holed, or caked-beyond-cleaning bars throw drippings in the wrong direction and cause the uneven flames people often blame on the burner or regulator. A clean Flavorizer bar is the cheapest fix for a lot of flame problems.
What is the Weber QCC1 regulator and does it fail?
QCC1 is the propane connection standard Weber uses on every current gas grill. The regulator rarely fails outright, but it has a bypass mode that trips when the tank valve is closed too fast — the fix is a 60-second reset procedure, not a new part. If the reset does not restore full flow, then order Weber's 30-inch hose-and-regulator kit (part 7627 for Genesis 300) or the 21-inch universal (part 7502).
Do generic third-party burners fit a Weber grill?
Some fit dimensionally, but the orifice size and venturi angle on a generic burner is often off, which causes the uneven flames and hot knobs Weber's troubleshooting guide warns about. Order the Weber OEM burner tube through weber.com/parts or an authorized dealer — it is the one Weber part generic alternatives routinely get wrong.
Was this guide helpful?
Shopping for Weber?
See Weber products
